Thời điểm dữ liệu: · Đã xuất bản: · Cập nhật chậm: dữ liệu đã hơn 8 ngày.
Ảnh đang chuẩn bị
Ảnh sản phẩm đang được chuẩn bị.
thông số 241dẫn chứng [n]nguồn 2
Chưa có giá công khai đã xác minh. Hãy yêu cầu báo giá từ nhà bán.
1
Thêm vào giỏ của trình duyệt này — không cần tài khoản hay thông tin liên hệ.
Giá ở đây là giá niêm yết của nhà phân phối nên trang này không thanh toán — báo giá sẽ cho biết điều kiện thực tế.
Vận chuyển · thời gian giao[giá trị]
Thông số.
Kiểm tra trước khi đặt hàng.
mục · keygiá trịcâu nguyên vănnguồnDẫn chứngThu thập · Thay đổi
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +1.00.01 N·m
câu nguyên văn14 +1.0 +0.2 –
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.20.002 N·m
câu nguyên văn14 +1.0 +0.2 –
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +1.60.016 N·m
câu nguyên văn17 +1.6 +0.3 -0.2
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.30.003 N·m
câu nguyên văn17 +1.6 +0.3 -0.2
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 17 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -0.2-0.002 N·m
câu nguyên văn17 +1.6 +0.3 -0.2
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 20 / 50; 40 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +2.40.024 N·m
câu nguyên văn20 +2.4 +0.5 -0.3
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.50.005 N·m
câu nguyên văn20 +2.4 +0.5 -0.3
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 20 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -0.3-0.003 N·m
câu nguyên văn20 +2.4 +0.5 -0.3
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +4.00.04 N·m
câu nguyên văn25 +4.0 +0.8 -0.5
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.80.008 N·m
câu nguyên văn25 +4.0 +0.8 -0.5
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 25 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -0.5-0.005 N·m
câu nguyên văn25 +4.0 +0.8 -0.5
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +7.00.07 N·m
câu nguyên văn32 +7.0 +1.4 -1.0
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +1.40.014 N·m
câu nguyên văn32 +7.0 +1.4 -1.0
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 32 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -1.0-0.01 N·m
câu nguyên văn32 +7.0 +1.4 -1.0
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +130.13 N·m
câu nguyên văn40 +13 +2.4 -1.7
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 40 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -1.7-0.017 N·m
câu nguyên văn40 +13 +2.4 -1.7
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +1.00.01 N·m
câu nguyên văn14 +1.0 +0.2
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.20.002 N·m
câu nguyên văn14 +1.0 +0.2
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +1.60.016 N·m
câu nguyên văn17 +1.6 +0.3
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.30.003 N·m
câu nguyên văn17 +1.6 +0.3
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 20 / 50; 40 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +2.40.024 N·m
câu nguyên văn20 +2.4 +0.5
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.50.005 N·m
câu nguyên văn20 +2.4 +0.5
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +4.00.04 N·m
câu nguyên văn25 +4.0 +0.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.80.008 N·m
câu nguyên văn25 +4.0 +0.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +7.00.07 N·m
câu nguyên văn32 +7.0 +1.4
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +1.40.014 N·m
câu nguyên văn32 +7.0 +1.4
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantity Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +130.13 N·m
câu nguyên văn40 +13 +2.4
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.275 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +1.00.01 N·m
câu nguyên văn14 +1.0 +0.2 –
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.20.002 N·m
câu nguyên văn14 +1.0 +0.2 –
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +1.60.016 N·m
câu nguyên văn17 +1.6 +0.3 -0.2
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.30.003 N·m
câu nguyên văn17 +1.6 +0.3 -0.2
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 17 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -0.2-0.002 N·m
câu nguyên văn17 +1.6 +0.3 -0.2
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 20 / 50; 40 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +2.40.024 N·m
câu nguyên văn20 +2.4 +0.5 -0.3
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.50.005 N·m
câu nguyên văn20 +2.4 +0.5 -0.3
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 20 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -0.3-0.003 N·m
câu nguyên văn20 +2.4 +0.5 -0.3
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +4.00.04 N·m
câu nguyên văn25 +4.0 +0.8 -0.5
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +0.80.008 N·m
câu nguyên văn25 +4.0 +0.8 -0.5
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 25 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -0.5-0.005 N·m
câu nguyên văn25 +4.0 +0.8 -0.5
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +7.00.07 N·m
câu nguyên văn32 +7.0 +1.4 -1.0
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +1.40.014 N·m
câu nguyên văn32 +7.0 +1.4 -1.0
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 32 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -1.0-0.01 N·m
câu nguyên văn32 +7.0 +1.4 -1.0
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn +130.13 N·m
câu nguyên văn40 +13 +2.4 -1.7
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Bù mô-men không tảino_load_torque_compensation
giá trịđiều kiện đo Mục trong catalogue SHD-2UH · Thời gian chạy rà Torque value is measured after 2 hours at 2000rpm input. · Tải khi đo No-load running torque is the torque which is required to rotate the
input side (high speed side), when there is no load on the output side
(low speed side). · Tốc độ đầu vào khi chạy rà Torque value is measured after 2 hours at 2000rpm input. · Cách đo Ratio 100
Lubricant Grease
lubrication Name Harmonic Grease SK-1A (size 20 or more)
Harmonic Grease SK-2 (size 14, 17)
Quantiy Recommended quantity (See page 281）
Torque value is measured after 2 hours at 2000rpm input. · Cách bù No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2). · Cấu hình trong catalogue Size / Ratio: 40 / 120 · Tỷ số giảm tốc tham chiếu No-load running torque of the gear varies with ratio. Graphs 276-1
to 276-4 show the values for a reduction ratio of 100. For other
gear ratios, add the compensation values in the right-hand table
(Table 275-2).
nguyên văn -1.7-0.017 N·m
câu nguyên văn40 +13 +2.4 -1.7
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.13 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Tổn hao trễhysteresis_loss
giá trịđiều kiện đo Tải đo trễ ■ Hysteresis loss (Silk hat and cup style only)
As shown in Figure 020-1, when the applied torque is increased to
the rated torque and is brought back to [zero], the torsional angle
does not return exactly back to the zero point This small difference
(B – B') is called hysteresis loss. · Cấu hình trong catalogue Size / Ratio: 14 / 50
nguyên văn 7.32.51 arcmin
câu nguyên văn50 ×10-4rad 7.3 5.8 5.8 5.8 5.8 5.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Tổn hao trễhysteresis_loss
giá trịđiều kiện đo Tải đo trễ ■ Hysteresis loss (Silk hat and cup style only)
As shown in Figure 020-1, when the applied torque is increased to
the rated torque and is brought back to [zero], the torsional angle
does not return exactly back to the zero point This small difference
(B – B') is called hysteresis loss. · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more; 17 / 50; 20 / 50; 25 / 50; 32 / 50; 40 / 50
nguyên văn 5.81.994 arcmin
câu nguyên văn50 ×10-4rad 7.3 5.8 5.8 5.8 5.8 5.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Tổn hao trễhysteresis_loss
giá trịđiều kiện đo Tải đo trễ ■ Hysteresis loss (Silk hat and cup style only)
As shown in Figure 020-1, when the applied torque is increased to
the rated torque and is brought back to [zero], the torsional angle
does not return exactly back to the zero point This small difference
(B – B') is called hysteresis loss. · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more; 20 / 80 or more; 25 / 80 or more; 32 / 80 or more; 40 / 80 or more
nguyên văn 2.90.997 arcmin
câu nguyên văn80 or
more ×10-4rad 5.8 2.9 2.9 2.9 2.9 2.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 14 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.02 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 17 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 3.93.9 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 20 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 7.07 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 25 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1414 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 32 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2929 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 40 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5454 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 14 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.96.9 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 17 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1212 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 20 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2525 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 25 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4848 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 32 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 108108 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 40 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 196196 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.292900 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.676700 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.111000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.020000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.747000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 8.888000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.373700 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.888800 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.313000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.727000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.161000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 11110000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.474700 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.212000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.020000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 3.737000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 8.484000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 15150000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.92.372 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.81.994 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.42.2 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.22.131 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.12.097 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50; 32 / 80 or more; 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 144.813 arcmin
câu nguyên vănθ2 ×10-4rad 19 14 19 18 18 18
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.44000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.848400 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.313000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.727000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.161000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 11110000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.444400 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.949400 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.717000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 3.737000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 7.878000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 14140000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.616100 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.313000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.525000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.747000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 11110000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 20200000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.01.719 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.61.581 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.41.856 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.21.788 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.81.65 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.91.684 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 165.5 arcmin
câu nguyên vănθ2 ×10-4rad 16 13 15 13 14 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more; 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 134.469 arcmin
câu nguyên vănθ2 ×10-4rad 16 13 15 13 14 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 155.157 arcmin
câu nguyên vănθ2 ×10-4rad 16 13 15 13 14 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-03Thay đổi —
Tổn hao trễhysteresis_loss
giá trịđiều kiện đo Tải đo trễ ■ Hysteresis loss (Silk hat and cup style only)
As shown in Figure 020-1, when the applied torque is increased to
the rated torque and is brought back to [zero], the torsional angle
does not return exactly back to the zero point This small difference
(B – B') is called hysteresis loss. · Cấu hình trong catalogue Size / Ratio: 14 / 50
nguyên văn 7.32.51 arcmin
câu nguyên văn50 ×10-4rad 7.3 5.8 5.8 5.8 5.8 5.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Tổn hao trễhysteresis_loss
giá trịđiều kiện đo Tải đo trễ ■ Hysteresis loss (Silk hat and cup style only)
As shown in Figure 020-1, when the applied torque is increased to
the rated torque and is brought back to [zero], the torsional angle
does not return exactly back to the zero point This small difference
(B – B') is called hysteresis loss. · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more; 17 / 50; 20 / 50; 25 / 50; 32 / 50; 40 / 50
nguyên văn 5.81.994 arcmin
câu nguyên văn50 ×10-4rad 7.3 5.8 5.8 5.8 5.8 5.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Tổn hao trễhysteresis_loss
giá trịđiều kiện đo Tải đo trễ ■ Hysteresis loss (Silk hat and cup style only)
As shown in Figure 020-1, when the applied torque is increased to
the rated torque and is brought back to [zero], the torsional angle
does not return exactly back to the zero point This small difference
(B – B') is called hysteresis loss. · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more; 20 / 80 or more; 25 / 80 or more; 32 / 80 or more; 40 / 80 or more
nguyên văn 2.90.997 arcmin
câu nguyên văn80 or
more ×10-4rad 5.8 2.9 2.9 2.9 2.9 2.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 14 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.02 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 17 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 3.93.9 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 20 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 7.07 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 25 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1414 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 32 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2929 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 40 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5454 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 14 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.96.9 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 17 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1212 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 20 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2525 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 25 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4848 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 32 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 108108 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 40 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 196196 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.292900 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.676700 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.111000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.020000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.747000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 8.888000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.373700 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.888800 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.313000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.727000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.161000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 11110000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.474700 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.212000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.020000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 3.737000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 8.484000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 15150000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.92.372 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.81.994 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.42.2 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.22.131 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.12.097 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50; 32 / 80 or more; 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 144.813 arcmin
câu nguyên vănθ2 ×10-4rad 19 14 19 18 18 18
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.44000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.848400 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.313000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.727000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.161000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 11110000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.444400 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.949400 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.717000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 3.737000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 7.878000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 14140000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.616100 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.313000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.525000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.747000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 11110000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 20200000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.01.719 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.61.581 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.41.856 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.21.788 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.81.65 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.91.684 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 165.5 arcmin
câu nguyên vănθ2 ×10-4rad 16 13 15 13 14 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more; 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 134.469 arcmin
câu nguyên vănθ2 ×10-4rad 16 13 15 13 14 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates torsion almost proportional to
the torque on the output side. Figure 018-1 shows the torsional
angle at the output side when the torque applied on the output
side starts from zero, increases up to +T0 and decreases down to
–T0. This is called the “Torque – torsion angle diagram,” which
normally draws a loop of 0 – A – B – Aʼ – Bʼ – A. The slope
described in the “Torque – torsion angle diagram” is represented
as the spring constant for the stiffness of the HarmonicDrive®
gear (unit: Nm/rad).
As shown in Figure 020-1, this “Torque – torsional angle diagram”
is divided into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 155.157 arcmin
câu nguyên vănθ2 ×10-4rad 16 13 15 13 14 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdf · p.11 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Tổn hao trễhysteresis_loss
giá trịđiều kiện đo Tải đo trễ ■ Hysteresis loss (Silk hat and cup style only)
As shown in Figure 020-1, when the applied torque is increased to
the rated torque and is brought back to [zero], the torsional angle
does not return exactly back to the zero point This small difference
(B – B') is called hysteresis loss. · Cấu hình trong catalogue Size / Ratio: 14 / 50
nguyên văn 7.32.51 arcmin
câu nguyên văn50 ×10-4rad 7.3 5.8 5.8 5.8 5.8 5.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Tổn hao trễhysteresis_loss
giá trịđiều kiện đo Tải đo trễ ■ Hysteresis loss (Silk hat and cup style only)
As shown in Figure 020-1, when the applied torque is increased to
the rated torque and is brought back to [zero], the torsional angle
does not return exactly back to the zero point This small difference
(B – B') is called hysteresis loss. · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more; 17 / 50; 20 / 50; 25 / 50; 32 / 50; 40 / 50
nguyên văn 5.81.994 arcmin
câu nguyên văn50 ×10-4rad 7.3 5.8 5.8 5.8 5.8 5.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Tổn hao trễhysteresis_loss
giá trịđiều kiện đo Tải đo trễ ■ Hysteresis loss (Silk hat and cup style only)
As shown in Figure 020-1, when the applied torque is increased to
the rated torque and is brought back to [zero], the torsional angle
does not return exactly back to the zero point This small difference
(B – B') is called hysteresis loss. · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more; 20 / 80 or more; 25 / 80 or more; 32 / 80 or more; 40 / 80 or more
nguyên văn 2.90.997 arcmin
câu nguyên văn80 or
more ×10-4rad 5.8 2.9 2.9 2.9 2.9 2.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 14 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.02 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 17 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 3.93.9 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 20 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 7.07 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 25 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1414 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 32 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2929 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 40 · Vùng độ cứng xoắn T1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5454 N·m
câu nguyên vănT1 Nm 2.0 3.9 7.0 14 29 54
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 14 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.96.9 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 17 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1212 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 20 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2525 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 25 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4848 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 32 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 108108 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Mô-men chuyển tiếp xoắntorsional_transition_torque
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Ký hiệu cỡ trong catalogue Size: 40 · Vùng độ cứng xoắn T2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 196196 N·m
câu nguyên vănT2 Nm 6.9 12 25 48 108 196
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.292900 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.676700 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.111000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.020000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.747000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 8.888000 N·m/rad
câu nguyên vănRatio
50 K1 ×104Nm/rad 0.29 0.67 1.1 2.0 4.7 8.8
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.373700 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.888800 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.313000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.727000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.161000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 11110000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.37 0.88 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.474700 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.212000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.020000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 3.737000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 8.484000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 15150000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.47 1.2 2.0 3.7 8.4 15
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.92.372 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.81.994 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.42.2 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.22.131 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 50 · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.12.097 arcmin
câu nguyên vănθ1 ×10-4rad 6.9 5.8 6.4 7.0 6.2 6.1
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 50; 32 / 80 or more; 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 144.813 arcmin
câu nguyên vănθ2 ×10-4rad 19 14 19 18 18 18
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.44000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.848400 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.313000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.727000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 6.161000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 11110000 N·m/rad
câu nguyên vănRatio
80 or
more K1 ×104Nm/rad 0.4 0.84 1.3 2.7 6.1 11
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.444400 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.949400 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.717000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 3.737000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 7.878000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 14140000 N·m/rad
câu nguyên vănK2 ×104Nm/rad 0.44 0.94 1.7 3.7 7.8 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 0.616100 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 1.313000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 2.525000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.747000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 11110000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Độ cứng xoắntorsional_stiffness
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn K3 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 20200000 N·m/rad
câu nguyên vănK3 ×104Nm/rad 0.61 1.3 2.5 4.7 11 20
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.01.719 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.61.581 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.41.856 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 5.21.788 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 32 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.81.65 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ1 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 40 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 4.91.684 arcmin
câu nguyên vănθ1 ×10-4rad 5.0 4.6 5.4 5.2 4.8 4.9
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 14 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 165.5 arcmin
câu nguyên vănθ2 ×10-4rad 16 13 15 13 14 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 17 / 80 or more; 25 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 134.469 arcmin
câu nguyên vănθ2 ×10-4rad 16 13 15 13 14 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
Góc chuyển tiếp xoắntorsional_transition_angle
giá trịđiều kiện đo Tính chất giá trị * The values in this table are reference values. The minimum value is approximately 80% of the displayed value. · Vùng độ cứng xoắn θ2 · Cách đo ■ Stiffness
Fixing the input side (wave generator) and applying torque to the
output side (flexspline) generates a torsional angle almost
proportional to the torque on the output side. Figure 020-1 shows
the torsional angle at the output side when the torque applied on
the output side starts from zero, increases up to +T0 and
decreases down to –T0. This is called the “Torque – torsion angle
diagram,” which normally draws a loop of 0 – A – B – Aʼ – Bʼ – A.
The slope described in the “Torque – torsion angle diagram” is
represented as the spring constant for the stiffness of the
HarmonicDrive® gear (unit: Nm/rad).
As shown in Figure 020-2 “Spring Constant Diagram” is divided
into 3 regions, and the spring constants in the area are
represented by K1, K2 and K3.
K1 ···· The spring constant when the torque changes from [zero] to [T1]
K2 ···· The spring constant when the torque changes from [T1] to [T2]
K3 ···· The spring constant when the torque changes from [T2] to [T3]
■ See the corresponding pages of each series for values of the
spring constants (K1, K2, K3) and the torque-torsional angles
(T1, T2, - θ1, θ2). · Cấu hình trong catalogue Size / Ratio: 20 / 80 or more · Tỷ lệ giá trị tối thiểu * The values in this table are reference values. The minimum value is approximately 80% of the displayed value.
nguyên văn 155.157 arcmin
câu nguyên vănθ2 ×10-4rad 16 13 15 13 14 14
nguồnhttps://www.harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdf · p.273 · Tài liệu nhà sản xuất
Dẫn chứngCó nguồn
Thu thập · Thay đổi2026-09-06Thay đổi —
thông số 241, hiển thị 241
Tài liệu gốc.
2 nguồn đã đọc giá trị
2 tài liệu
harmonicdrive.net/_hd/content/documents1/SHD-2UH-2SH_GearUnits.pdfTài liệu nhà sản xuất · 164 giá trịRetrieved 2026-09-03
harmonicdrive.net/_hd/content/documents1/reducer%20catalog_US.pdfTài liệu nhà sản xuất · 77 giá trịRetrieved 2026-09-06
Tải xuốngChưa công bố tệp gốc: chưa quyết định tài liệu nào được công bố.
Không thay đổi
2026-09-03thu thập lần đầu · 2 nguồn
Cập nhật kế tiếp2026-10-01
Lưu lịch sử thay đổi
Dựng một khớp quanh linh kiện này.
Khi xác định được nhóm, linh kiện này có thể đưa vào tổ hợp khớp.
Xem tổ hợp khớpJOINT · SHD-2UH · Chưa phân loại
Trạng tháiKhông áp dụng
- Chưa phân loại nhóm
Cần xác nhận trước khi kết luận
Nhà cung cấp.
Nhà trưng bày WRC 2026 Bắc Kinh và các nhà cung cấp khác.
Linh kiện của nhà cung cấp này 1,815Trang nhà cung cấp
Phương án thay thế đang chuẩn bị
Giữ linh kiện này trong BOM.
Khi BOM mở, bạn có thể gom linh kiện lại và gửi một yêu cầu duy nhất.