数据采集时间: · 发布时间: · 更新延迟:公开数据已超过8天。
实物照片 · 来源 aifitlab.com
1 / 1
1 / 1规格 10依据 [n]来源 1
配送 · 交期[数值]
规格。
下单前请核对。
项目 · key数值原文语句来源依据采集 · 变更
额定电压rated_voltage
数值
6 – 8.4 V DC
原文语句Operating Voltage 6 – 8.4 V DC
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
堵转电流stall_current
数值测试条件 额定电压 6 – 8.4 V DC
≤2.0 A
原文语句Stall Current ≤2.0 A
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
堵转扭矩stall_torque
数值测试条件 额定电压 6 – 8.4 V DC
≥6.0 kgf·cm
原文语句Stall Torque ≥6.0 kgf·cm
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
空载转速no_load_speed
数值测试条件 额定电压 6 – 8.4 V DC
≤0.13 sec/60°
原文语句No-load Speed ≤0.13 sec/60°
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
重量weight
数值测试条件 额定电压 6 – 8.4 V DC
原文 19 g0.019 kg
原文语句Weight 19 g
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
通信方式protocol
数值测试条件 额定电压 6 – 8.4 V DC
TTL/UART (single-wire half-duplex)
原文语句Communication Interface TTL/UART (single-wire half-duplex)
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
回差backlash
数值测试条件 额定电压 6 – 8.4 V DC
≤1°
原文语句Backlash ≤1°
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
脉宽范围pulse_width_range
数值测试条件 额定电压 6 – 8.4 V DC
0 – 4096
原文语句Pulse Width Range 0 – 4096
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
待机电流idle_current
数值测试条件 额定电压 6 – 8.4 V DC
≤30 mA
原文语句Static Current ≤30 mA
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
输出轴output_shaft
数值测试条件 额定电压 6 – 8.4 V DC
25T / D5
原文语句Output Shaft 25T / D5
来源https://aifitlab.com/products/dspower-ds-s009k-servo-motor · 经销商页面
依据有出处
采集 · 变更2026-08-28变更 —
规格 10 中显示 10
原文文档。
读取数值的来源 1 个
文档 1
下载原始文件尚未公开 —— 哪些文档可以公开尚未决定。
无变更
2026-08-28首次采集 · 来源 1 条
下次更新2026-10-01
保留变更记录
JOINT · DS-S009K · B · Motors
状态待确认
- 缺少关节比对所需规格
- 无判定 —— 所需规格键尚未确定
判定前需确认的事项